<div dir="ltr"><div><div>Hello Utkarsh,<br><br></div>Well in fact I have used both. I had used a python script before, which gave a similar behavior, but in that case the unusual large intervals were about 15 minutes instead of 8 hours. I also noticed that there was something wrong in my setup using the python script, so when I redid the animation I simply used the GUI to check the setup more rigorously and decided not to use the python script. <br>
<br></div>A bit more info on the python script:<br><div><br>With the python script I also assumed it may have been related to the actual screen being rendered at the moment that the large intervals showed up. This because I used VNC to log into the machine for rendering and the screen was locked with ParaView running for most of the time. I just unlocked the screen occasionally to have a look at the progress from time to time and I could imagine this may have influenced the rendering. Later I also saw a 15 min. interval between two pngs which were created in the middle of the night, meaning the screen was probably still locked, so I assumed that me unlocking the screen could not have been the reason. Fifteen minutes between two frames can be accepted if this happens once in 100 frames or so, but 8 hours is just too much. <br>
<br></div><div>At the moment I started the animation from the GUI again, but with the &quot;Cache Geometry&quot; unchecked as you suggested. I will check the results of that setting tonight.<br><br></div><div>Regards,<br>
Tom<br></div></div><div class="gmail_extra"><br><br><div class="gmail_quote">2013/1/14 Utkarsh Ayachit <span dir="ltr">&lt;<a href="mailto:utkarsh.ayachit@kitware.com" target="_blank">utkarsh.ayachit@kitware.com</a>&gt;</span><br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Tom,<br>
<br>
I wonder if caching is causing these issues. Are you using the<br>
ParaView GUI or a Python script? If  the GUI, can you disable caching<br>
(uncheck &quot;Cache Geometry&quot; from the &quot;Animation&quot; page in the &quot;Settings&quot;<br>
dialog.<br>
<br>
Utkarsh<br>
<div><div class="h5"><br>
On Mon, Jan 14, 2013 at 5:50 AM, Tom Fahner &lt;<a href="mailto:tom.fahner@gmail.com">tom.fahner@gmail.com</a>&gt; wrote:<br>
&gt; Dear all,<br>
&gt;<br>
&gt; For some reason I noticed that ParaView has some large intervals between<br>
&gt; writing a PNG for consecutive frames of an animation. Normally there is<br>
&gt; about one minute between the timestamp of two PNGs, but sometimes there is<br>
&gt; suddendly a gap of 8 hours:<br>
&gt;<br>
&gt;  141K Jan 13 15:56 New_Volume_.0118.png<br>
&gt;  141K Jan 13 15:58 New_Volume_.0119.png<br>
&gt;  139K Jan 13 15:59 New_Volume_.0120.png<br>
&gt;  139K Jan 13 16:00 New_Volume_.0121.png<br>
&gt;  138K Jan 14 00:34 New_Volume_.0122.png<br>
&gt;  139K Jan 14 00:35 New_Volume_.0123.png<br>
&gt;  139K Jan 14 00:36 New_Volume_.0124.png<br>
&gt;<br>
&gt; There are multiple occasions where these large intervals happen but this<br>
&gt; does not happen at a regular interval of the animation. There does seem to<br>
&gt; be a relation with the amount of memory that is used, since there is a<br>
&gt; sudden decrease in memory used right after &quot;Jan 14 00:34&quot;. Below I will<br>
&gt; describe my animation and setup. I hope anyone can give an explanation for<br>
&gt; the behavior.<br>
&gt;<br>
&gt; During the weekend I have created an animation of a mixing tank using volume<br>
&gt; rendering of the concentration of some chemicals in the tank. It is a<br>
&gt; reasonably large CFD simulation performed with OpenFOAM. There are about 15<br>
&gt; million cells (tetrahedrals and prismatic layer), but not extremely large. I<br>
&gt; saved the concentration every 0.25 seconds for a 120s simulation. We have<br>
&gt; ParaView 3.98.0 installed on this machine and it was the only program<br>
&gt; running at the time. I have made the animation with ffmpeg after ParaView<br>
&gt; made the frames as consecutive pngs. Besides the volume rendering of the<br>
&gt; concentration, the walls of the tank where shown with a fixed opacity of 0.3<br>
&gt; and the internal structure (some rotors and baffles) where present as well.<br>
&gt; Although the simulation use the MRF concept, I did mimick the rotation of<br>
&gt; the rotors using the transform filter. Using the &quot;cool to warm&quot; preset for<br>
&gt; visualization I could nicely set the opacity to 0 when the concentration was<br>
&gt; in the allowed range and it showed red in case of too high concentration, of<br>
&gt; blue when too low. The resulting animation is satisfactory, I just wonder<br>
&gt; what can be done to make sure these large intervals between writing images<br>
&gt; do not happen.<br>
&gt;<br>
&gt; Hope someone can help, if you need more information, please let me know.<br>
&gt;<br>
&gt; Regards,<br>
&gt; Tom<br>
&gt;<br>
&gt; --<br>
&gt; T.C. Fahner<br>
&gt; e: <a href="mailto:tom.fahner@gmail.com">tom.fahner@gmail.com</a><br>
&gt;<br>
&gt;<br>
</div></div>&gt; _______________________________________________<br>
&gt; Powered by <a href="http://www.kitware.com" target="_blank">www.kitware.com</a><br>
&gt;<br>
&gt; Visit other Kitware open-source projects at<br>
&gt; <a href="http://www.kitware.com/opensource/opensource.html" target="_blank">http://www.kitware.com/opensource/opensource.html</a><br>
&gt;<br>
&gt; Please keep messages on-topic and check the ParaView Wiki at:<br>
&gt; <a href="http://paraview.org/Wiki/ParaView" target="_blank">http://paraview.org/Wiki/ParaView</a><br>
&gt;<br>
&gt; Follow this link to subscribe/unsubscribe:<br>
&gt; <a href="http://www.paraview.org/mailman/listinfo/paraview" target="_blank">http://www.paraview.org/mailman/listinfo/paraview</a><br>
&gt;<br>
</blockquote></div><br><br clear="all"><br>-- <br>T.C. Fahner<br>e: <a href="mailto:tom.fahner@gmail.com">tom.fahner@gmail.com</a><br>t: +31-6-52642814<br>a: van Lodensteynstraat 24<br>    2612 SE Delft<br>    Netherlands
</div>